How much does an infrared panel heater cost to run?

Infrared panel: ~16p/h for 600 W at Ofgem cap; EST 350–900 W typical. CSE: same £/year as panel heaters for a flat; can worsen damp. Calculator.

By the Wisiko editorial team · Updated 9 November 2026 · 7 min read

Estimated cost over the period
—
Per hour at full power (all panels)
—
Per day
—
Per week
—
Electricity over the period
—

Same hours, same tariff, one 2 kW fan or convector heater at full power (CSE typical rating)

2 kW fan heater or convector heater
—

Formula: kWh = watts ÷ 1,000 × hours × share of time heating. Without a measurement, the only figure that is sourced is full power: the panel’s rated watts for the whole hour. How much a thermostat saves depends on the room, the insulation and the outside temperature: a plug-in energy meter gives your real figure. Results are indicative estimates based on the values you enter. Always check your appliance labels, your tariff and the manufacturer’s data.

Was this calculation useful?
Key points
  • At the Ofgem cap (26.32p/kWh, 1 Oct–31 Dec 2026) a 600 W infrared panel costs about 16p an hour at full power, a 400 W one about 11p and an 850 W one about 22p.
  • The Energy Saving Trust says wall panels for homes typically range from 350 to 900 W and use similar amounts of electricity to other panel heaters.
  • The Centre for Sustainable Energy puts infrared panels at about £1,080 a year for a flat, the same as ordinary panel heaters: infrared changes how the heat feels, not how many units a watt uses.
  • Both warn that infrared panels can make damp and mould worse, because they do not warm the air.

Pick a panel size (or type the wattage from the rating plate), the number of panels, the hours they are switched on and, if you know it, the share of time they are actually heating. The calculator gives the cost per hour, day, week and for your chosen number of days at your tariff. The price field is pre-filled with the Ofgem price cap, which you can replace with your own rate.

Formula

kWh = watts ÷ 1,000 × hours × share of time the panels are on × number of panels

An infrared panel is a resistive electric heater: the Centre for Sustainable Energy notes that electric room heaters are considered 100 % efficient because all the electricity is converted into heat. The difference with a convector heater is how that heat reaches you. The Energy Saving Trust explains that infrared panels warm the surfaces and people they face by radiation, the way the sun does, rather than warming the air first. The power rating therefore sets the cost per hour exactly as for any other electric heater.

Cost per hour by panel size (UK price cap, full power)

PanelPer hour4 hours30 days × 4 h
300 W (smallest Dimplex IRP)8p32p36 kWh ≈ £9.48
400 W (Herschel Select XLS)11p42p48 kWh ≈ £12.63
600 W (Dimplex IRP, Herschel Select XLS)16p63p72 kWh ≈ £18.95
850 W (largest Dimplex IRP)22p89p102 kWh ≈ £26.85
900 W (top of the Energy Saving Trust range)24p95p108 kWh ≈ £28.43
1,200 W (largest Herschel Inspire)32p£1.26144 kWh ≈ £37.90
2,000 W fan or convector heater, for comparison53p£2.11240 kWh ≈ £63.17

Price: Ofgem Direct Debit average of 26.32p/kWh for 1 October to 31 December 2026, which excludes the standing charge (you pay it whether or not you run a heater). The panel sizes are the ratings published on the manufacturer pages listed below (Dimplex IRP 300, 600 and 850 W; Herschel Select XLS 400 and 600 W; Herschel Inspire, seven sizes from 250 to 1,200 W). The Energy Saving Trust says wall panels designed for homes typically range from 350 to 900 W. The 2 kW line uses the typical rating the Centre for Sustainable Energy gives for fan and convector heaters. All of these are full-power figures calculated here from the rated watts, not measurements of a particular product.

A panel is cheaper per hour because it is smaller, not because infrared is a different kind of electricity. A 600 W panel and a 2 kW fan heater do not deliver the same heat: the comparison only says what you pay for an hour of each.

What the Centre for Sustainable Energy and the Energy Saving Trust say about cost

  • Same running cost as panel heaters. The Centre for Sustainable Energy’s electric heating guide (reviewed June 2026) lists infrared panels at about £1,080 a year for a flat, the same figure as ordinary panel heaters, based on 27.69p/kWh and its typical consumption for a flat. That is 3,900 kWh × 27.69p; at today’s 26.32p the same 3,900 kWh would be about £1,026 (our own conversion). It lists installation at £100 to £200 per heater.
  • Possibly cheaper if well controlled. The Energy Saving Trust says a well-controlled infrared system will probably cost less to run than standard electric panel heaters, because you may feel warm enough in direct view of a panel while the air temperature is lower elsewhere, but adds that there is little research to confirm this. We have found no independent measurement of the saving, so the calculator does not assume one: use the “share of time heating” field if you have measured your own duty.
  • Not a whole-house replacement for gas. The Energy Saving Trust says electricity costs about four times as much as gas for the same energy, and that a heat pump typically uses two to four times less electricity than infrared heating for the same heat.
  • Good for topping up one room. The Energy Saving Trust suggests a portable infrared heater to keep yourself warm while the rest of the house is empty, so the main heating can be turned off or down.

Who infrared panels suit, and who they do not

The Centre for Sustainable Energy says infrared radiant panels work best where people spend a lot of time sitting in one place, or in very draughty homes where warm air would quickly be lost. It adds that you feel colder if you are not in front of the panel, “like sitting in the shade”, and that there is no warmth lingering in the air once the heater is off.

If your home has damp or mould, the Centre for Sustainable Energy does not recommend this type of heating, and the Energy Saving Trust lists condensation, damp and mould among the risks, in particular in cold spots away from the panel. Whatever heating you use, check regularly for damp and keep the room ventilated.

Thermostats and controls

The Centre for Sustainable Energy notes that radiant heaters rarely have thermostats or timers, which can make their running costs higher over long periods, and that room heaters are most cost-effective with a built-in thermostat. Check this before buying, because for the models below the control is sold separately:

  • Dimplex states that its IRP panels are used with a DTB-2R wall-mounted digital thermostat, for Lot 20 compliance, giving 7-day time and temperature control.
  • Herschel’s Select XLS panels work with its SmartLED thermostats, which are sold separately, and its Inspire picture panels must be controlled with Herschel IQ controllers, also sold separately.

Which? found in its heater tests that a heater with a thermostat toggles on and off once the set temperature is reached, so it does not run continuously and costs less than a full-power hour. It also found that cheap dial thermostats are rarely 100 % accurate.

Room size

Manufacturer area guides are only a starting point. Herschel states 6–8 m² for its 400 W Select XLS and 11–13 m² for the 600 W, assuming a medium to well insulated space with a 2.4 m ceiling, and says the figures are a guide only. A bigger room, a higher ceiling or poor insulation means more watts, or more panels, and the cost per hour rises in proportion: two 600 W panels cost 32p an hour at full power.

Infrared panel, oil-filled radiator or fan heater?

All three convert each kWh into a kWh of heat, so the bill depends on watts and hours. The oil-filled radiator gives out heat gradually for a while after the element switches off, the fan heater warms a small room fast, and the infrared panel warms what is in front of it quickly but leaves nothing behind when it stops. The space heater page has the general calculator with US and UK rates. Which? sums up the trade-off for portable electric heaters: they are cheaper for a short-term blast in a small area, but over a full day you are probably better off sticking to central heating.

For a sense of scale, Which? says the electric heaters it tested cost anything from 8p to 80p an hour on full blast, so the choice of model matters as much as the type.

Infrared panel or gas central heating?

At the current cap a kWh of electricity costs 26.32p and a kWh of gas 7.97p, a ratio of about 3.3 before any boiler loss. To compare an hour of your own gas heating with a heater, see the gas central heating cost per hour page, and for all fuels side by side the heating cost by fuel page. If you want to heat yourself rather than the room, an electric blanket uses far less electricity per hour, and a heated towel rail is a small thermostatic bathroom heater.

Safety

  • The Energy Saving Trust says portable panels, like any portable heater, can cause burns or a fire: switch them off when you are not in the room and unplug them at night or when you go out.
  • Never cover a panel or let it tip over. Some models switch off automatically if they overheat or tip.
  • Surface temperatures are not low: Herschel gives 95–105 °C for its Select XLS and Inspire panels, and the Energy Saving Trust says they can be hotter than a standard radiator, though usually under 100 °C. Keep panels at a safe height, out of reach of young children and pets.
  • Wall- or ceiling-mounted panels are wired in: the Energy Saving Trust recommends speaking to a specialist installer and getting at least three quotes.

The price cap can change

The 26.32p/kWh rate applies from 1 October to 31 December 2026. Ofgem announces the cap for 1 January to 31 March 2027 by 25 November 2026; until it does, any forecast is only a forecast. Replace the price in the calculator with the rate on your bill, and see your electricity bill in context for the other appliances.

Frequently asked questions

How much does a 600W infrared panel cost to run per hour?

600 W is 0.6 kW, so at the Ofgem cap of 26.32p/kWh it costs about 16p for every hour it draws full power (0.6 × 26.32p = 15.8p). Four hours at full power cost about 63p. With a thermostat the panel switches off part of the time, so that is a maximum, not a typical bill.

Are infrared heaters cheaper to run than other electric heaters?

Per hour of full power, no: a watt is a watt. The Energy Saving Trust says infrared panels use similar amounts of electricity to other panel heaters, and the Centre for Sustainable Energy gives both the same running cost for a flat (about £1,080 a year at 27.69p/kWh). The Energy Saving Trust adds that a well-controlled infrared system will probably cost less than standard panel heaters if you feel warm enough at a lower air temperature, but that little research is available to confirm it.

Is infrared heating cheaper than gas central heating?

Not as whole-house heating. The Energy Saving Trust says electricity costs about four times as much as gas for the same amount of energy and does not advise replacing gas central heating with infrared panels throughout a house. At the current cap, 26.32p for a kWh of electricity against 7.97p for a kWh of gas is a ratio of about 3.3 before boiler losses. Topping up one room for a few hours can still make sense.

Can infrared panels cause damp and mould?

They can. Both the Centre for Sustainable Energy and the Energy Saving Trust warn that infrared panels heat people and surfaces rather than the air, so if the air stays cold, moisture condenses more easily on cold walls and windows. The Centre for Sustainable Energy does not recommend this type of heating in a home that already has damp or mould problems.

Can I leave an infrared heater on overnight?

The Energy Saving Trust says portable panels should be switched off when you are not in the room and unplugged at night or when you go out. Panels fixed to a wall or ceiling by an installer may be designed for night use, but you should check with the installer first. Never cover a panel.

How big an infrared panel do I need?

Manufacturers give a guide by floor area: Herschel states 6–8 m² for its 400 W Select XLS panel and 11–13 m² for the 600 W one, for a medium to well insulated room with a 2.4 m ceiling, and says this is only a guide. A draughty or poorly insulated room needs more. The Energy Saving Trust notes that a room may need more than one panel for even coverage.

Sources

  1. Centre for Sustainable Energy – Electric heating (reviewed June 2026: infrared radiant panels, running cost for a flat at 27.69p/kWh, installation cost, damp and mould)
  2. Centre for Sustainable Energy – Room heaters (reviewed January 2026: typical power ratings, radiant heaters and thermostats, infrared heaters and damp)
  3. Energy Saving Trust – Infrared heating explained (wattage range, comparison with panel heaters, gas and heat pumps, safety)
  4. Dimplex – IRP far-infrared panel heater (300, 600 and 850 W models, DTB-2R thermostat)
  5. Herschel – Select XLS LED infrared panel heater (400 and 600 W, heated area guide, surface temperature)
  6. Herschel – Inspire infrared picture panel heater (seven sizes from 250 to 1,200 W)
  7. Which? – Best electric heaters 2026 (fan heater tests: cost per hour at 26.32p/kWh, thermostat behaviour, electric heaters versus central heating)
  8. Ofgem – Energy price cap unit rates and standing charges (1 October to 31 December 2026)

Related

Energy

How much does it cost to run a space heater?

US: ~27¢/h for 1,500 W at EIA Aug 2026 rates; UK: Which? averages 33p oil-filled, 48p convector, 60p fan. Thermostat cuts real cost. Calculator.

Calculator

How much does an oil-filled radiator cost to run?

Oil-filled radiator: Which? average 33p/h on high (vs 60p fan). At Ofgem cap, 1.5 kW ≈39p/h max, 2 kW ≈53p. Heat lingers ~30 min after off. Calculator.

Calculator

How much does gas central heating cost per hour?

A combi boiler costs £2.15 an hour flat out (27 kWh of gas at the Ofgem cap) and 43–63p at its lowest setting. A typical home averages £2.37 a day.

Calculator

How much does heating cost by fuel type?

Heating oil costs about 11.2p per kWh of fuel (12.45p of useful heat) in Nov 2026 vs 7.97p for gas under the Ofgem cap. Oil vs gas vs pellets calculator.

Calculator

How much does an electric blanket cost to run?

100 W × 3 h × 120 nights = 36 kWh: ≈ £9.48 at the UK cap or $6.54 at the US average — 10× less than a 1 kW heater. Calculate yours.

Calculator

Heat pump vs electric heaters: how much could you save?

Compare the yearly cost of electric heaters and a heat pump from your heating use. At a measured seasonal efficiency of 3.4, the bill falls by over two thirds.

Calculator

How much does a heated towel rail cost to run?

200 W × 4 h × 180 days ≈ 144 kWh (≈ £38 at the UK cap). Calculate by wattage, hours and season.

Calculator

Appliance running cost calculator

Enter an appliance's wattage and daily use to get kWh and running cost per hour, day, month and year at UK, US or European prices, or your own rate.